


2608 Soft Loop Ratchet Strap Tie Downs
What sets Hydralift's Tie-Downs apart for other Tie-downs:

Proudly Made in the USA and DOT Approved
Non-Scratch Soft-Loop Tie-Downs with Twice the Strength:
While the trend in our industry is to import cheaper, inferior webbing products from other countries, Hydralift supports the USA and manufactures all webbing with 100% first quality yarns. In addition, our cargo straps are F.A.A. & DOT approved.
-
- Made in the USA Easy to Use Non-Slip Ratchet
- 2,500 lb Assembly Strength 883 lb Working Load Limit
- 3,500 lb Industrial Webbing 3,300 lb Ratchet Strength
- Heavy Duty Vinyl Coated Hooks Built-in Soft Extensions
- Corrosion & Rust Resistant Rust Resistant
- Extended Life vs other straps Hydralift Grey
Soft Loops
Hydralift has sewn soft loops on both sides of our HL2608 Tie-Down. The soft loops can be used when you are connecting to chrome, or a painted surface that you want a little more protection against scratching or marring. In addition the soft loop can reach around a larger surface for example the Motorcycle’s triple crown to get a better contact point when tying down your motorcycle
Specifications
Breaking Strength Capacity: The minimum load a component or assembly will withstand before failure. Remember, all assemblies are only as strong as the weakest component used to make them.
Working Load Limit: The maximum load capacity that any given component or assembly should be subjected to during use. Hydralift highly recommends the “working load limit” does not exceed one third (1/3) the “breaking strength capacity” of the component or assembly being used. Working load limits shown on this website are rated at one third of the minimum breaking strength (for example, a strap rated at 2,500 lbs would have a working load limit of 833 lbs).
Rating Load Capacity: Ratings are generally established and/or regulated by industry or legislative standards and may vary from industry to industry. It is the owner’s and user’s responsibility to determine suitability of a product for any particular use. It is recommended that all applicable industry, trade association, federal, state and local regulations are adhered to. Read all operating instructions and warnings carefully. All ratings shown on this website are based on the product being new and used in normal environmental conditions. All products should be inspected regularly. Any worn, deformed, misused or overloaded products should be replaced immediately.
Caution: When securing your motorcycle never use a worm type tie down, they can become loose while traveling and have poor dependability qualities. Use only a ratchet type tie down shown below. Hydralift now offers a superior quality ratchet tie down, with a built in soft extension and twice the strength of most other brands of tie downs.
TDA3401 Add-On Eye Type Anchor for 4288-85

Add on Anchor Eye TDA3401 Machined to fit HL4288/85 lifts
The TDA3401 is specially machined from a solid block of steel to provide maximum strength for this Tie-Down Anchor . The Anchors are machine to fit perfectly into the HL motorcycle tie down arm anchor location.
- Never use eye bolts as they will crush/disfigure the tie down arms and the eye bolts will come loose.
- This can not happen with the TDA3401 as they are machined to the diameter and height of the anchor locations.
- Set of 4 Anchors EZ Bolt-on No Drilling
TDF32 Forward Tie-Down Anchor for 4288-85 Lifts

EZ INSTALL

DIRECT BOLT-ON

NO DRILLING

ADDITIONAL 2 ANCHOR LOCATIONS
The Forward Tie Down Anchor Mount adds an additional set of tie-down anchor locations to the furthest location of the motorcycle ramp. This moves your tie-downs straps out and away from your fiberglass faring also providing added security and stability for larger size motorcycles.
Designed for the larger motorcycles that have a full front fairing as with the Honda Goldwing and Harley Ultra type motorcycles. The front wheel stop can still be moved forward or back to center your motorcycle on the Hydralift
HLWC39 Automatic Wheel Chock for 4288-85 Lifts

EZ INSTALL

Honda Goldwing

Harley Dresser
The Forward Tie Down Anchor Mount adds an additional set of tie-down anchor locations to the furthest location of the motorcycle ramp. This moves your tie-downs straps out and away from your fiberglass faring also providing added security and stability for larger size motorcycles.
Designed for the larger motorcycles that have a full front fairing as with the Honda Goldwing and Harley Ultra type motorcycles. The front wheel stop can still be moved forward or back to center your motorcycle on the Hydralift
4210RA 10" Wide Ramp Adapter for HL4288/85 Lifts

EZ INSTALL

4210RA
The 4210RA is a specially made to accommodate a 10" fat rear motorcycle tire. This adapter is a drop in adapter that widens the HL motorcycle ramp to 10" at the entrance side of the ramp to allow the loading of a "Fat Rear Tire" . The adapter is reinforced under the ramp saddle to the factory ramp and adds a modified dove tail for loading and unloading.
The 4210RA can also be used to raise the rear of the motorcycle when additional clearance is needed for some motorcycles.
Fits all Hydralift Motorcycle Lifts with M090 SN.